Limit switch for liquids,Process connection G1,Suitable for process temperatures up to 150 °C (302 °F),Rugged stainless steel housing,Onsite function check possible thanks to LED indication,External function test with test magnet

Measuring method : The tuning fork is brought to its resonance frequency by means of a piezoelectric drive. If the tuning fork is covered by liquid, this frequency changes. The electronics monitor the resonance frequency and indicate whether the tuning fork is freely vibrating or is covered by liquid.
Construction type : device with short tube
Operating mode : MAX = maximum safety:
The device keeps the electronic switch closed as long as the liquid level is below the fork.
example application: overspill protection
MIN = minimum safety:
The device keeps the electronic switch closed as long as the fork is immersed in liquid.
example application: dry running protection of pumps
The electronic switch opens if the limit is reached, if a fault occurs or in the event of a power fails (quiescent current principle)
Connection : This device may be used with any sequential circuit, as long as the circuit can support the electrical circuit values of the switching elements.
Rated voltage : 10 ... 35 V DC
Fusing : external 500 mA slow
Current consumption : < 15 mA
Power consumption : 975 mW
Residual ripple : 5 V ss at 0 ... 400 Hz
Measured variable : density
Measurement range : min. 0.7 g/cm3
Output type : switch output
Switching current : max. 250 mA
Electromagnetic compatibility :
Electromagnetic compatibility : NE 21
Degree of protection : IEC 60529
Shock resistance : EN 60068-2-27
Vibration resistance : EN 60068-2-64
Climate class : DIN EN 60068-2-38/IEC 68-2-38
Reference operating conditions : - ambient temperature: 25 °C (+77 °F)
- process pressure: 1 bar (14.5 psi)
- fluid: water (density: approx. 1 g/cm3, viscosity: 1 mm2/s)
- medium temperature: 25 °C (+77 °F)
- density setting: > 0.7 g/cm3
- switching time delay: standard (0,5 s, 1 s)
Measured value resolution : < 0.5 mm
Measuring frequency : approx. 1100 Hz in air
Switching point : 13 mm ± 1 mm
Non-repeatability : ± 1 mm acc. to DIN 61298-2
Hysteresis : max. 3 mm
Influence of ambient temperature : negligible
Influence of medium temperature : -25 µm/°C
Influence of medium pressure : -20 µm/bar
Switching time : - 0.5 s when tuning fork is covered
- 1.0 s when tuning fork is uncovered
Switch-on delay : max. 3 s
Installation conditions :
Ambient conditions :
Process conditions :
Degree of protection : IP65 , NEMA 4X
Connection : valve connector M16
Material : process connection and short tube: stainless steel 316L (1.4401/1.4435)
tuning fork: stainless steel 316L
housing cover and connector: PPSU
Surface quality : Ra < 3.2 µm
Mass : approx. 169 g
Process connection : thread G1 acc. to ISO 228
Display elements : The LED display is on the connection side.
- green LED: indication of ready to operate
- red LED: fault indication
- yellow LED: operating mode indication
Function test : function test with test magnet (optional accessory)
CSA approval : cCSAus Listed, General Purpose
Overspill protection : see approval (ZE)
Supplementary documentation : technical information (TI)
manual (BA)
approval (ZE)
Supplementary information : Statement of Conformity, Declaration of Conformity, Attestation of Conformity and instructions have to be observed where applicable. For information see www.pepperl-fuchs.com.
Designation : see technical information (TI)

  • SKU : LVL-A7-BG4B-E5PU-CG-EMS
  • 型号 : LVL-A7-BG4B-E5PU-CG-EMS
  • 最小起订量 : 1
  • 单位 : CNY